Bunn-O-Matic Corporation
9
2
INSTRUCTIONS (Continued)
14. Install valve and bracket assembly by
feeding the attached tubing through
the smaller snap bushings in the base
of the machine.
13. Remove top nut off of grounding stud
in the base of the machine, add on the
green grounding wire from the new har-
ness and reinstall the nut onto the stud.
Make sure that all the other grounding
wires remain on the ground stud.
12. Plug wire harness (supplied with kit)
into Auto Fill board connector and route
wires back into the machine.
11. Install provided bushings into product/
water holes to protect the tubing.
10. Remove hole covers from the base of
the machine as needed to route water
and product tubing through base.
9. Reinstall the main board into the
machine using the original mounting
screws.
17. Position the valve and bracket assembly
between the right front corner post and
the right side fan shroud and secure
with screws provided.
16. Route Pink and Tan wires up to level
probes and attach using nuts provided.
Pink is the right probe and Tan is the
left probe.
15. Connect the wires to the fill valves both
water and product as needed according
to the wiring schematic provided. Red
and White wires to the right valve(s),
Blue and white wires to the left valve(s).
Please note that Left and Right are from
the front of the machine, Users left and
right.
37570 072706
3
INSTRUCTIONS (Continued)
20. Remove one or both plugs from the hop-
per depending on whether a separate
water line is being installed. Install the
quick disconnect fitting into the hole on
the hopper and secure with nut provided
with fitting.
19. Assemble a .25” quick disconnect fit-
ting, 1.25” neoprene tube and barbed
elbow as shown with the .50” barb
pointing down.
18. Reinstall front panel, left panel and both
motor covers.
37570 102711
22. Route the tubes from the solenoids up
to the quick disconnect fittings on the
hoppers. The tubes are supplied with
extra length to allow for trimming if
desired. Slip a clamp over the end of
the tube and install a .25” male discon-
nect fitting. Position the clamp over the
barb area of the fitting and crimp into
place.
NOTE: Make certain the tubes are routed
to the correct hoppers to prevent product
from being mixed or hoppers overflowing.
21. Install hoppers onto machine and
slide probes onto hoppers into slots
provided.
23. Connect the tubes to the hoppers.
(continued)
25. Route the tubes from the solenoids
together and connect to hopper fitting.
24. Install hoppers onto machine and
slide probes onto hoppers into slots
provided.
26. Slide hopper fitting into place in the
slot on the hopper.
Early models with quick disconnect fittings,
follow steps 19 through 23.
Late models with new hopper slide fitting
skip to step 24 through 26.
Early Models
Late Models
2
INSTRUCTIONS (Continued)
14. Install valve and bracket assembly by
feeding the attached tubing through
the smaller snap bushings in the base
of the machine.
13. Remove top nut off of grounding stud
in the base of the machine, add on the
green grounding wire from the new har-
ness and reinstall the nut onto the stud.
Make sure that all the other grounding
wires remain on the ground stud.
12. Plug wire harness (supplied with kit)
into Auto Fill board connector and route
wires back into the machine.
11. Install provided bushings into product/
water holes to protect the tubing.
10. Remove hole covers from the base of
the machine as needed to route water
and product tubing through base.
9. Reinstall the main board into the
machine using the original mounting
screws.
17. Position the valve and bracket assembly
between the right front corner post and
the right side fan shroud and secure
with screws provided.
16. Route Pink and Tan wires up to level
probes and attach using nuts provided.
Pink is the right probe and Tan is the
left probe.
15. Connect the wires to the fill valves both
water and product as needed according
to the wiring schematic provided. Red
and White wires to the right valve(s),
Blue and white wires to the left valve(s).
Please note that Left and Right are from
the front of the machine, Users left and
right.
Early Models