CSA8UP,TDS8UP,CSA8BUP,TDS8BUP,CSA82UP, and TDS82UP Option XP Instructions

Instructions

CSA8UP, TDS8 UP, CSA8BUP, TDS8BUP, CSA82UP,

and TDS82UP

Option XP

TDS8000 and CSA8000 Series Instruments

Microsoft Windows XP Upgrade Kit

071-2156-00

*P071215600*

071215600

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are c overed by U.S. a nd foreign pa tent s, issued and pendi ng. Information in this publicat ion superce des

that in all previously published material. Specifications and price change privileges reserved.

TEKT RONIX and TE K a re registered t rademarks o f Tektronix, Inc .

Windows is a registered tradem ark of Microsoft Corpora tion in the Unit ed States and othe r countries.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Dri ve

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

H In North America, call 1-800-833-9200.

H Worldwide, visit www.tektronix.com to find contacts in your area.

CSA/TDS8UP, CS A/TDS8BUP, and CSA/TDS 82UP Option XP Upgrade Kit

Kit Description and Installation

This kit includes hardware and software to upgrade your CSA8000, TDS8000,

CSA8000B, TDS8000B, CSA8200, and TDS8200 instruments from Microsoft

Windows 2000 to Windows XP.

NOTE. Installation of the Microsoft Windows XP operating system requires that

the instrument currently has the Microsoft Windows 2000 operating system

installed.

Tektronix installation service (Option IF) is available for this upgrade. If

installation service is desired, please contact the service center in your region to

schedule installation.

Products

CSA8000 All serial numbers (if previously upgraded to Windows 2000)

TDS8000 All serial numbers (if previously upgraded to Windows 2000)

CSA8000B All serial numbers (if previously upgraded to Windows 2000)

TDS8000B All serial numbers (if previously upgraded to Windows 2000)

TDS8200 All serial numbers

CSA8200 All serial numbers

Kit Parts List

Quantity Part number Description

1ea 071--2156--00 Kit Instruct ions: Windows 2000, CSA8000 and TDS8000

Series

1ea 650--5047--xx Hard drive: Windows XP and 8000 Series product software

pre-installed

1ea 020--2786--xx 8000 Series product soft ware CD-ROM designed for

Microsoft W indows XP

1ea 020--2787--xx 8000 Series Windows XP Operating System Restore:

5 CD-ROMs, Document

1ea 063--3860--xx BIOS Update CD--ROM

1ea 063--3868--xx Microsof t W indows XP C ert ifi cate of Authenticity Label

(This label must be applied to t he instrument after

installation is complete.)

Kit Description and Installation

CSA/TDS8UP, CS A/TDS8BUP, and CSA/TDS 82UP Option XP Upgrade Kit

Installation

These instructions are for personnel who are familiar with servicing the product.

If you need further details for disassembling or reassembling the product, refer to

the appropriate service manual. Contact your nearest Tektronix, Inc., Service

Center or Tektronix Factory Service for installation assistance.

CAUTION. To prevent static discharge damage, service the product only in a

static-free environment. Observe standard handling precautions for static-sensi-

tive devices while installing this kit. Always wear a grounded wrist strap,

grounded foot strap, and static resistant apparel while installing this kit.

Before installing the new hard disk drive, you must have the correct BIOS

installed. Do the following procedure to check the BIOS version and update if

necessary.

1. Power on the instrument.

2. While the instrument is booting, press F2 to enter the BIOS setup.

3. Check the first line of the BIOS display. The first line of the BIOS display

should be the BIOS version number. The BIOS version must be 1.03.03.

4. If the BIOS is 1.03.03 or greater:

a. Exit the BIOS setup without making any changes.

b. Power off the instrument.

5. If the BIOS is a version less than 1.03.03:

a. Exit the BIOS setup without making any changes.

b. After the instrument is finishes the boot cycle, insert the BIOS CD

contained in this kit.

c. Follow the update prompts provided with the CD. BIOS update

instructions are also located on the Readme file located on the CD.

d. After the BIOS update is finished, power off the instrument.

Check Instrument BIOS

Kit Description and Installation

CSA/TDS8UP, CS A/TDS8BUP, and CSA/TDS 82UP Option XP Upgrade Kit

Access and remove the old hard drive using the procedure below. If you need

additional instructions, see the service manual for the product you are servicing.

Follow these procedures to remove the hard drive:

CAUTION. Do not remove the replaceable hard disk drive when the instrument is

powered on.

The replaceable hard disk drive may be permanently damaged if it is removed

while the instrument is powered on.

1. Set the instrument so that its bottom is down on the work surface and its rear

panel is facing you.

2. Prepare to remove the hard disk drive:

a. Verify that the chassis is powered off and unplugged.

b. Push the hard disk drive cover in and the hard drive will disconnect from

the latch.

c. Grasp the hard disk drive assembly and slide it out of the instrument.

Remove the

hard disk drive

Depress

the latch

3. Lay the hard disk drive assembly face down.

4. Remove the four #0 phillips screws that fasten the hard disk drive to the

cartridge.

Replace Hard Disk Dr ive

Kit Description and Installation

CSA/TDS8UP, CS A/TDS8BUP, and CSA/TDS 82UP Option XP Upgrade Kit

Remove 4 screws

5. Carefully remove the hard disk drive from the cartridge, disconnecting the

ribbon cable from the hard disk drive.

6. Insert the new hard disk drive (from this kit) into the cartridge, connecting

the ribbon cable to the hard disk drive.

7. Reinstall the four phillips screws to fasten the hard disk drive to the

cartridge.

8. Push the hard disk drive chassis back into the instrument.

Verify Operation

Successful startup and product software launch verifies operation. No further

verification is needed. If the New Device Found dialog box appears, refer to the

Possible Driver Problems section for information on how to proceed.

Apply Windows XP Authenticity Label

Place the Windows XP Certificate of Authenticity label on the rear panel of the

instrument. This is an important step to show that the instrument is licensed to

run the Windows XP operating system.

Possible Driver Problems

In some instances, the new hard drive may cause the New Device Found dialog

message to display. The two most likely causes are the need for reinstallation of

device drivers.

If the New Device Found dialog box displays and requires the drivers for the

National Instruments GPIB card, follow these steps along with the dialog box.

1. Select No -- Not at this time to not search the internet for drivers.

National Instruments GPIB

Kit Description and Installation

CSA/TDS8UP, CS A/TDS8BUP, and CSA/TDS 82UP Option XP Upgrade Kit

2. Select Next.

3. Select Install Software Automatically.

4. Select Next.

5. Select Finish.

If the New Device Found dialog box displays and requires the drivers for the

Tektronix Power PC Board, follow these steps along with the dialog box.

1. Select No -- Not at this time to not search the internet for drivers.

2. Select Next.

3. Select Install Software Automatically.

4. Select Next.

NOTE. If the driver cannot be located automatically, you will need to browse to

its location at c:\Tektronix\Tektronix custom.

5. Select Finish.

g End of document g

Tektronix Power PC Board